Cisco 827 ADSL
(Score this article) 
Loading ... 
Consultation Forum of the Cisco 827 ROUTER
NOTE: pasatealinux clarification, not all of the 800 series routers are used for ADSL, 20 megs. The only people who used to adsl 20 megs are some of the 870 series, like the 877 and 877w, some of the 1800 series (specifically the 1801 and 1841) and some later.
- Cisco 800 series configuration interface eth0
- Cisco 800 series configuration dynamic telefonica
Cisco SEIE 800 configuration in Multi
cisco 800 series opening ports for emule
cisco 800 series configuration 20 megs of Jazztel
cisco 800 series configuration dynamic orange
cisco 800 series parameters Synchronism
Cisco 827 configuration with Wanadoo ADSL DYNAMIC Submitted by Peter.
[url = downloads / downloads / ROUTERS ADSL / Cisco 827 recursive = yes]
If you have any house in this section you can send it by pressing HERE.
February 21st, 2008 at 11:02 pm
Hello everyone.
Well, this is the first time I write and I do help asking, I have a Cisco router so I purchased 877 a week ago and can not configure it for dynamic IP addresses of Telefonica, I am using the Cisco SDM interface, input configuration does not work, the way it works uncica connection is it on the way IP Negotiated is, does the connection test but from a PC connected to the router can not get out to the Internet, to make a connection test is ok and I can do ping from the router to the Internet or from a PC to the router, but not from the PC to the Internet, I have tried everything and the truth that I have not ever worked with the console, try to install the old router CRWS coming much more clearly the SDM today but I could not either, so I'm good at rolling with it to see if anyone has any idea how to configure this router specifically for dynamic IP Telefonica by Cisco SDM, I think it should be an issue of the routes, but not which was put in order AYUDAAAAAAAAAAAAA
Gilfre
May 23rd, 2008 at 5:06 pm
[...] [...] Cisco 827
July 30th, 2008 at 3:49 a.m.
Hola buenas noches que tal? I have configured a router 851 and mounted on a remote site, in fact I can access without any problem either by vpn or telnet, the problem I have is that I can not reach the VLAN 1, and the bone set, but if ping command somewhere in my computer network simply does not work when I ping, let's show you the interfaces have to suggest.
Greetings!
interface FastEthernet0
!
interface FastEthernet1
!
interface FastEthernet2
shutdown
!
interface FastEthernet3
shutdown
!
interface FastEthernet4
description ES_WAN $ $
ip address xxx.xxx.xxx.xxx 255.255.255.240
no ip redirects
no ip unreachable
no ip proxy-arp
ip nat outside
ip virtual-reassembly
no ip route-cache
duplex auto
speed auto
crypto map SDM_CMAP_1
!
interface Vlan1
description $ ETH-SW-LAUNCH $ $ intf-INFO-HWIC 4ESW $
no ip address
ip nat inside
ip virtual-reassembly
no ip route-cache
ip tcp adjust-mss 1452
bridge-group 1
!
!
ip local pool EZVPN_POOL_1 172.16.0.201 172.16.0.206
ip forward-protocol nd
!
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
!
logging trap debugging
access-list 100 remark SDM_ACL Category = 128
access-list 100 permit ip any host 255.255.255.255
access-list 100 permit ip any 127.0.0.0 0,255,255,255
access-list 100 permit ip any 201,144,242,224 0.0.0.15
access-list 101 remark EZVPN_ACL_1
access-list 101 remark SDM_ACL Category 4 =
access-list 101 permit ip any 172.16.0.0 0.0.0.255
!
control-plane
!
bridge 1 protocol ieee
bridge 1 route ip
banner login ^ CCAuthorized access only!
Disconnect IMMEDIATELY if you are not an authorized user! ^ C
!
line with 0
no modem enable
transport output telnet
line aux 0
transport output telnet
line vty 0 4
7 password 05080F1C2243
transport input telnet ssh
!
scheduler max-task-time 5000
scheduler allocate 4000 1000
scheduler interval 500
end
Router800 #
July 30th, 2008 at 3:55 a.m.
jaja ups I forgot, it already has VLAN 1 ip and becomes:
interface Vlan1
description $ ETH-SW-LAUNCH $ $ intf-INFO-HWIC 4ESW $
ip address 172.16.0.5
ip nat inside
ip virtual-reassembly
no ip route-cache
ip tcp adjust-mss 1452
bridge-group 1
thanks!
August 12th, 2008 at 7:43 pm
Hello George,
says unable to reach the ip of the VLAN and any machine on the network. You mean from the VPN router or the same?
A simple test is to check if it is properly connected to the LAN.
Enter "show ip interface brief" look and the interface VLAN 1 is the protocol "up."
It could be a problem ARP, with the command "show arp" should be able to see the IPs of the machines with their Mac address.
If you think that is well connected and is not closed the VLAN interface, check that a port is not disabled in error, "show interface status."
Greetings
September 6th, 2008 at 12:58 p.m.
Hello everyone.
Well, I wrote here earlier asking for help and with the bad luck that no one has answered me yet.
Well, I have the 877 configured for Cisco IP Phones Dinamica Megas 3, if you need someone to write to me is gilfremh yahoo.
My problem now is that this router connected to a network with several routers and switches, the routes already set in the 877 seems to be all right, because from my PC to get all these devices and I replied without any problem pings, the thing gets ugly when I go out to the Internet from any computer behind the router, it is impossible, try to configure NAT for these subnets but I do not work, let them proceed in the situation of these teams to see if anyone can help.
Cisco 877 (192.168.1.1)
! !
! !
! ! My PC (192.168.1.100
!
! Switch
!
! Router 2 (192.168.1.2 - 192.168.2.2) Network 2.0/24)
()! PC 192.168.2.10
()
()
Router 3 (192.168.2.3 - 192.168.3.3) Network 3.0/24)
! PC 192.168.3.10
My PC can access all the other routers and all pings respond through Cisco router 877
Since the PCs in the sub 2.0/24 or 3.0/24 tambie'n can access all but I can not go online, but if I go from my PC to the Internet.
Agardecido Well in advance and hope someone will help.
Sincerely
Gilfre